Why an intake fan belongs at the bottom of your rack
Warm air rises, so the most effective way to cool a rack is to feed cool air in low and let it exhaust up high. The AC Infinity CLOUDPLATE T9-N is the intake half of that plan: it mounts in a standard 19-inch rack and draws room air through the front panel. Pair it with an exhaust fan at the top, and the rack moves cool air from bottom to top instead of recycling warm air.
This guide walks through mounting, wiring, and setting the thermostat so the fans only work when the rack actually needs it.
What the CLOUDPLATE T9-N provides
- AC Infinity CLOUDPLATE T9-N Quiet Rack Cooling Fan System - Intake: Three 120 mm fans move 60 to 300 CFM across six speeds at 12 to 38 dBA. You get a wide range of airflow and noise levels, so you can choose a quiet setting for a listening room or ramp up for heavier loads.

AC Infinity CLOUDPLATE T9-N Quiet Rack Cooling Fan System - Intake - AC Infinity CLOUDPLATE T9-N Quiet Rack Cooling Fan System - Intake: At 5.25 inches tall and 2 inches deep it takes three rack spaces and almost no depth. This shallow depth means it can fit in furniture-style racks where deeper fan panels won't go.
- AC Infinity CLOUDPLATE T9-N Quiet Rack Cooling Fan System - Intake: The 6-foot stainless probe reads the rack where the heat collects. A corded probe lets you monitor the hottest spot, not just the fan's own intake, so the thermostat responds to your equipment.
Mount and wire the T9-N
Before you start, confirm you have an open 3U space near the bottom of your rack and access to a wall outlet for the included 6-foot power adapter.
- Choose the mounting location: Select an open 3U space near the bottom of the rack. Cool air enters low, so this position feeds fresh air to the components above.
- Secure the fan unit: Use the four included rack screws to bolt the CLOUDPLATE T9-N into the rack rails. The frame is brushed black aluminum with CNC-machined corners.
- Connect power: Plug the included 6-foot power adapter into the POWER jack on the fan unit and then into a wall outlet.
- Place the temperature probe: Plug the 6-foot stainless probe into the PROBE jack. Tie its head near the hottest component—typically a multi-channel amplifier or home theater receiver—using the included wire ties. Keep the probe away from the fans so it reads equipment heat, not airflow.
Set the thermostat for quiet, automatic cooling
The CLOUDPLATE T9-N uses an LCD thermostat to control the fans. Press the Mode button until AUTO appears, then set your start temperature. In AUTO mode, the fans start when the probe reaches your set temperature and stop once it falls below by the buffer you choose—2, 4, 6, or 8°F. This buffer prevents short cycling.
For the quietest operation, start with a low speed and a small buffer. The fans run as low as 12 dBA, which is below typical room noise, so you may not hear them at all. If your equipment runs hot, increase the speed or adjust the buffer.
You can also use SPEED mode to fix a level from 0 to 6, or SMART mode to step the speed down one level per buffer step under the setting. An alarm temperature runs the fans at full speed and beeps until the rack cools. Readings can be shown in Fahrenheit or Celsius.
To prevent accidental changes, hold the Leaf button to lock the panel. A quick tap turns the display off while everything keeps running.
Checkpoints for a successful install
- Verify probe placement: The probe should be near the hottest component and away from the fans. Use the included wire ties to secure it.
- Confirm airflow direction: The T9-N draws air in through the front panel. Make sure the front of the rack is not blocked so cool room air can enter.
- Test the thermostat: After setting AUTO mode, watch the display to see the fans start and stop as the temperature changes. Adjust the buffer if they cycle too often.
- Consider a second fan for exhaust: For best results, pair the T9-N with an exhaust fan at the top of the rack. A daisy-chain cord, sold separately, lets the EXT port run a second CLOUDPLATE from this one controller.
Where the T9-N fits—and where it doesn't
The CLOUDPLATE T9-N is designed for standard 19-inch racks. It bolts to rack rails and does nothing on a shelf. If your components sit on open shelving, consider a component fan like the AC Infinity AIRCOM series instead.
This fan is particularly useful in racks left unattended, thanks to the high-temperature alarm and check-fan alert. It's also a good match for listening rooms where fan noise matters, since the low speeds are essentially silent. And because it's only 2 inches deep, it fits in shallow racks and furniture-style stands where deeper panels won't.


